How to Install a PVC Fence
There are a few things to be aware of if you're thinking of installing fence. The first step is to decide the place you'll be installing the fence. The next step is to prepare the ground. Then you need to place the posts. You may also have to alter the height of the fence depending on the size of your property.
Preparing the ground
It is crucial to prepare the ground for the fence. This is important because fence posts need to be securely installed. If they're not in a secure location, the fence will collapse in the wind.
Before you start digging, make sure to check with your local utility provider to ensure there are no underground utilities that could block the installation. In many areas, you can contact 811 and request that the utility company mark your yard for underground lines.
A gravel base should be laid for your fence posts. This will allow water to drain from the posts. It also provides a sturdy base for the blocks that will be put in.
Once you have the base, you can begin to install the vinyl fence. The material must be at least four feet long and 1 inch thick. You can employ an auger for digging the holes for fence posts if you have it.
Before digging, you must remove any plants or shrubs which could hinder the digging. Sometimes, it is easier remove the soil than dig it. If you must dig, you'll want to avoid digging in sandy or rocky soil.
Next, you will need to mark the high and low points of your yard. This can be done easily using a string level. Attach the string level to stakes that are about one foot above ground. The string level serves as a guideline for fence posts.
If your land is an extremely dry climate you'll probably require pre-drilling pilot holes. This will make the process easier.
You'll also have to mark the holes. Spray paint or markers to mark your holes. You can also use a mason's line to make sure that the posts are straight.
You can also fill the gap with decorative stones. These stones are suitable for smaller gaps. You'll have to find a different way to fill the larger gap. You can also try putting dirt into the gap. This is an affordable and cost-effective solution.
The postings are placed in the appropriate places.
It is often difficult to locate the posts. First, find the proper place. This can be done by a spirit level, a line mark painted to accommodate the width of the post or even a measuring wheel.
Then, put the end and corner posts in place. It is also recommended to install the middle and top rails. You may need to make some cuts. You could also use rails to act as an extra spacer between posts.
Once you've located the center of each hole using a tape measure or stakes and stakes, mark the middle of the posts using a tape measure. To determine the depth, you can also use the stringline. Once the string line is drawn, tie the ends of the end post to the string. This will ensure the fence will be straight.
After the posts have been securely seated and firmly seated, fill their bottoms with six inches of gravel. This will hold the posts in place and provide drainage.
Make use of a quick-setting concrete when putting fence posts in concrete. This is a type of concrete that sets in about three to four minutes. If you're installing privacy fencing, make sure not to overtighten the panels. The panels should be placed 22 inches above the ground. The panel should be secured using #10 1" self-tapping stainless steel screws.
The posts can be attached to your fence using two screws. It is recommended to leave one screw at each end of a privacy fence. Duct tape can be used to cover the bottom horizontal rails prior to putting them into the posts. This will prevent concrete from getting into the lower horizontal rail.
When you are satisfied with the layout, take off the duct tape and then insert the top rail into the posts. You can then connect the pickets to the rails.
You can also place the rails on the bottom at the corners. You can also use aluminum uchannels to attach the rails to the post.
Assembling the panels
The alignment of the fence posts up correctly is essential to the success of installing vinyl fence. Based on the design of your fence, you might require different methods. These steps can help you begin whether you want to install an oval or square fence.
Before you begin, ensure that you check your deed as well as local zoning laws. Also, notify neighbors of your plan. If you plan to install a vinyl fence, you might need to apply for an building permit.
Once all your posts are in place Once all your posts are in place, it's time to mount your rail brackets. These are screws that are attached to the inside face of the post. This makes it easier to manipulate of the posts as they are placed.
Before installing your rail brackets, install your bottom rail. Vinyl panels pre-assembled include two rails. You might need to modify the rails to suit your terrain.
Once the bottom rail is installed then you can put in the middle rail. The top rail can be put in place similarly. This process can website be completed with an aluminum u-channel. You can insert it into your posts with the help of #8 x 1'' screws.
You can then install your pickets one at a. Once your pickets have been installed then attach your C channel brackets. You can also put stakes around the corners to secure them in place. You can also use cotton string to connect the stakes.
You can also use a spray paint marker to mark your line. This will ensure that the fence is set when it is erected.
Finally, you need to install your privacy panels. They should be placed on the backside your fence. To help them stay in place, you can also add pea gravel. You can make your slope more gentle by placing your fence panels on one side so that they "step down". If the slope is steep your fence will need to be built in a manner that it "steps down".
Problems with changing heights
It might be difficult to align the posts when you want to put up a PVC fence. There are two methods to do it. One is to place the posts on the ground, and the alternative is to line them up. The first option is easier to implement and ensures that you have concrete under and around the post. In the second method, you have to remove the posts and then fill in with dirt.
When you remove the posts, be sure that you have a sufficient backfill and make holes that are deep enough to hold three-quarters the length of the post. You will need to dig down about six inches in order to place the posts into the base of the gravel. You may also employ a hole digger to make holes. The tension bar can be attached to the mesh at the end of the process. Then, staple the top of the mesh to the fence.
If you have difficulty aligning the posts, you can take rails from posts that are too high. It can be a complicated procedure, but you are likely to be able to complete it if you have two people with you. If you own a hammer and chisel, you can peen the threads of the bolts. This will keep them from escaping the fence when you take it out.